Car keys · Brantford
Ignition Lock Repair
The car arrived with one worn-looking key and a story about a lost spare.
In plain words
Most ignition lock work happens where the vehicle already is, a driveway, a parking lot, a curb, rather than requiring a tow to a shop first. The locksmith brings cylinder decoders, extraction tools and repinning equipment to the vehicle, assesses the mechanism in place, and works through accessory, on and start until the barrel turns the way it should. A shop visit only becomes necessary when the fault turns out to be electronic rather than mechanical.
How the visit goesAfter a slushy week the key barely reaches accessory before it stalls, gritty and reluctant, where it used to move cleanly through every position. Warming the car up in the driveway hasn't changed how the barrel feels at all.
Ignition Lock Repair
How the visit goes
Confirming who the vehicle belongs to
Before any tool touches the ignition, the locksmith confirms that the person requesting the work owns the vehicle or is authorized to have it serviced. A vehicle permit or registration document matched to a driver's licence is the simplest route, and a rental agreement, a fleet authorization, or a call to the registered owner fills the gap when the paperwork is not on hand. This step is a courtesy to every vehicle owner on the road, not an obstacle, and a careful locksmith treats it as the natural first step of the job rather than something to rush past.
Servicing the cylinder in place first
The first option is always the least invasive one: cleaning out the keyway, freeing a wafer that has stuck in a raised position, and lubricating the mechanism so the existing cylinder goes back to turning the way it should. This keeps the original hardware on the vehicle and avoids cutting a new key altogether when the fault turns out to be wear or contamination rather than a broken part. Only when this fails to restore normal behaviour does the barrel come out of the column.
One key doing everything it did before
If the doors and trunk already shared a key with the ignition, that arrangement is preserved or restored wherever the vehicle's design allows it, so the same key you carry now still opens everything it used to open before. Where a new key was cut, it is tested in every lock on the vehicle before the visit is called finished, not only in the ignition itself, so a lock quietly left out never becomes tomorrow's surprise.
Ignition Lock Repair
In the van
Plug follower
Pick and tension tools
Retaining pins and clips
Steering column trim tools
Dry graphite or PTFE lubricant
Ignition Lock Repair
What affects the quote
Keying other locks to match
Bringing the doors and trunk onto a newly pinned ignition key, so one key runs the whole vehicle again, is separate work from the ignition repair itself, even when it happens during the same visit.
Access through the steering column
Reaching some ignition cylinders means removing trim, shrouding or fasteners around the column first, and putting all of it back cleanly afterward. A column that is straightforward to open takes less time than one that is not.
Age and history of the vehicle
An older vehicle may have hardware that is harder to source, or wear built up over many years of daily use, while a vehicle with a known repair history gives the locksmith a clearer starting point.
What to have ready
- Does the key insert, turn partway, or not turn at all?
- Do the doors or trunk use the same key as the ignition?
- What is the vehicle's year, make and model?
Ignition Lock Repair: questions
QuestionsI just bought a used vehicle with one worn key. What should I expect?
A single worn key is a common starting point after buying used, and the visit usually has two parts: reading the existing wafers so a crisp new key can be cut, and deciding whether the barrel itself needs a service given whatever wear the previous owner's key left behind. Bringing whatever paperwork came with the sale helps confirm ownership before any work begins.
What if there are scratches or damage around my ignition slot already?
That is noted honestly before any work begins, since it often means an earlier attempt was made on the lock. Damage like this usually points toward a full cylinder and housing replacement rather than a simple service, because the internal parts of a lock that has already been forced are rarely trustworthy afterward. You are shown what was found before deciding how to proceed together.
Does cold or wet weather affect an ignition cylinder?
It can. Road salt, grit and moisture from a slushy season work their way into the keyway over time, and old grease inside the mechanism can stiffen in the cold. A barrel affected this way is cleaned, dried and treated with whatever lubricant the vehicle's own service information calls for, which helps it move freely through the next stretch of similar weather ahead.
Related services
- Car Key ReplacementThe car is yours now, but somebody else still holds a key to it.
- Spare Car Key DuplicationA lockout last month ended with a locksmith opening the door and going home, and the same single key has been carried ever since with nothing behind it.
- Key Fob ProgrammingA fob went missing weeks ago somewhere between a coat pocket and a parking lot, and a spare has covered the gap since.